Category Archives: manufacturing

EMA published concept paper on the visions of guidelines for influenza vaccines

The current regulatory requirements quality, nonclinical and clinical development of influenza vaccines are currently stated in several regulatory documents. These guidelines were drafted and appointed a different time points over several years before the onset of the major pandemics in 2009 -  2010.

The EMA has recognised a need to update the guidance of requiring the manufacturing, nonclinical and clinical development of complaints of vaccines. Especially in the light of novel vaccine technologies such as recombinant proteins, viruslike particles (the LPs) DNA or live viral vectors.

For these reasons the EMA may has issued this concept paper.

Excerpt from regulations

full text here

Regulatory requirements for the quality, non-clinical and clinical development of influenza vaccines are
currently stated in several documents including multidisciplinary guidelines such as
EMEA/CPMP/4986/03, CHMP/VWP/263499/06, the Note for guidance on harmonisation of requirements
for influenza vaccines CPMP/BWP/214/96 and the Guideline on dossier structure and content for
pandemic influenza vaccine marketing authorisation application (EMEA/CPMP/VEG/4717/03 rev. 1).
These guidelines were drafted and adopted at different time points and over several years before the
onset of the 2009-2010 influenza pandemic and each addresses one of seasonal influenza vaccines,
pre-pandemic or pandemic vaccines.
The need to update the available guidelines regarding the manufacturing, non-clinical and clinical
development of influenza vaccines was recognised during and following the 2009-2010 influenza
pandemic. More recently, issues encountered and experience gained during requests for CHMP
scientific advice and the processing of several applications for marketing authorisation of influenza
vaccines have underlined the desirability of updating the existing guidelines. In addition, it is
anticipated that novel influenza vaccines could be based on e.g. recombinant proteins, virus-like
particles (VLPs), DNA or live viral vectors and there is a need to consider the regulatory expectations
that would apply to such products.
Although current and future influenza vaccines may vary in nature and composition they all aim to
prevent clinically manifest influenza by means of eliciting a protective immune response. Therefore the
development of a single consolidated guidance document on the quality, non-clinical and clinical
requirements for influenza vaccines seems to be both feasible and appropriate.

 

EMA and FDA collaborate on inspections with Australia

Two pilot programs of collaboration on inspections between European medicines agency and its international partners in United States and Australia have been conducted successfully. The two programs focused on collaboration between international regulators for quality and safety.

Joint inspections on good clinical practice were undertaken in a large number of clinical programs, as well as joint inspections of active pharmaceutical ingredients manufacturing plants.

All agencies have agreed that the programs have been a success and will continue on this collaborative approach in future. This is clearly start of international recognition between the agencies inspection standards, which should have positive effects of mutual recognition and reduce the regulatory burden of companies operating internationally in our industry.

Excerpt  from announcement

Full Text Here

Two pilot programmes of collaboration on inspections between the European Medicines Agency (EMA) and its international partners in the United States and Australia have concluded successfully, according to two reports published today. The two programmes focus on increasing international regulatory collaboration among the regulatory agencies so that drug quality and safety can be enhanced globally.

The report on the joint good clinical practice (GCP) inspection pilot programme details the success of information-sharing and collaboration on inspections relating to clinical trials. Under the joint GCP inspection pilot, the EMA and the US Food and Drug Administration (FDA) exchanged more than 250 documents relating to 54 different medicines and, in conjunction with the GCP inspectors of the EU Member States, organised 13 collaborative inspections of clinical trials. This lays the foundation for a more efficient use of limited resources, improved inspectional coverage and better understanding of each agency’s inspection procedures. It demonstrates how the agencies can work together to improve the protection of participants in clinical trials and better ensure the integrity of data submitted as the basis for drug approvals.

The report on the joint active pharmaceutical ingredients (API) inspections pilot programme details the success of information-sharing and collaboration on API inspections among the participating authorities (EMA, France, Germany, Ireland, Italy, United Kingdom, EDQM, FDA and Australia’s Therapeutic Goods Administration (TGA)). Over the course of the 24-month pilot phase, the participants shared their surveillance lists and found 97 sites common to all three regions, resulting in the exchange of nearly 100 inspection reports and in nine joint inspections.

Both pilots involved the exchange of considerable amounts of information and the establishment of inspections carried out jointly by the agencies. This led to increased levels of understanding between the agencies, and a greater number of inspections of value to more than one authority.

Based on the positive experience in the two pilots, the agencies have agreed to continue with their collaboration on inspections, taking into account the experiences and lessons learned during the pilot phases.

 

FDA Publish Guidance on Container and Closure Systems Testing

FDA Publish Guidance on Container and Closure Systems Testing

Full Text Here

This guidance document provides recommendations to you, manufacturers, for using methods other than sterility testing to confirm container and closure system integrity as a part of the stability protocol for sterile biological products, human and animal drugs, and medical devices. This guidance document finalizes the draft guidance of the same title dated January 1998 (January 28, 1998, 63 Federal Register (FR) 4272).
Manufacturers of drugs and biologics purporting to be sterile must test each batch or lot, as the case may be, to ensure that the product in question conforms to sterility requirements. 21 CFR 211.167(a); 21 CFR 610.12. Such drugs and biologics are also subject to stability testing requirements. 21 CFR 211.166. The stability testing requirements include maintaining a written testing program designed to assess stability characteristics. Manufacturers of medical devices must validate processes, including sterilization for a device purporting to be sterile. 21 CFR 820.75. Stability testing should be part of the design validation of such devices. In vitro diagnostic products for human use are required to be labeled with stability information. 21 CFR 809.10. For products labeled as sterile, we consider sterility to be a stability characteristic.
The purpose of stability testing is to provide evidence on how the quality of a substance or product varies with time under the influence of a variety of environmental factors such as temperature, humidity, and light, which enables you to establish or modify recommended storage conditions, retest periods, and shelf life or dating period, as the case may be.2 This guidance document applies only to the replacement of the sterility test with an appropriate container and closure system integrity test in the stability written testing program (referred to in this guidanceas the “stability protocol”), recommending an alternative to sterility testing for supporting the continued capability of containers to maintain sterility. The guidance document does not apply to sterility testing methods for product sterility testing prior to release, as container and closure system integrity tests cannot demonstrate a product’s initial sterility.
This guidance document provides information that we recommend you consider when you propose using alternative methods to sterility testing to confirm the integrity of a container and closure system throughout the product’s shelf life or dating period. The recommendations in this guidance document apply to both pre- and post-approval stability protocols for sterile biological products, human and animal drugs, including investigational and bulk drugs. For medical devices, the recommendations in this guidance document apply to stability protocols for those devices labeled as sterile.
If you currently perform sterility testing as a stability-indicating test as part of a stability protocol, you may continue to do so. If your product is approved for an alternative to sterility testing as a component of your stability protocol, this document is not intended to recommend additional testing requirements.


For Assistance with Quality Aspects of Packaging Click Here

Damien Bové is THE Drug Development and Regulatory Consultant (pharmaceutical or biotechnology), I work with my clients to define a drug development target, define a drug development strategy, define a regulatory strategy or define a commercial strategy. Our clients are generally raising funds or looking to license out their technology and we help them achieve it. If you want to know more don’t hesitate to get in touch.

Avoid Expensive Mistakes, Keep On Top of New and Changing Regulations for Free!

Sign up for the most value add free newsource you can get for free. We spend a huge amount of time and effort monitoring the main drug / device regulators websites for changes in the regulatory environment, and capture between 20 and 40 new regulations, rules and initiatives each month, and summaries them in a fantastic FREE monthly Regulatory and Market Round Up. You can Un-Subscribe at any time and we don not share your details with anybody. You can’t afford to miss out on this service. Just fill in the form below.

Fill Out the Short Form Below…


  1. (required)


  2. (valid email required)

“Please note that the pages on this website are designed to provide you with general information only. We make no warranties, representations or undertakings about any of its content. This includes the completeness, accuracy and fitness for any particular purpose, or the content of any third party site referred to or accessed through it. You are personally responsible for ensuring that the information is correct and we will not be held liable or accountable for any mistakes that occur.”

FDA Publish Guidane on Media Fills for PET Drugs

FDA Publish Guidane on Media Fills for PET Drugs

Full Text Here

This guidance is intended to help manufacturers of positron emission tomography (PET) drugs meet the requirements for the Agency’s current good manufacturing practice (CGMP) regulations for PET drugs (21 CFR part 212). Most PET drugs are designed for parenteral administration and are produced by aseptic processing. The goal of aseptic processing is to make a product that is free of microorganisms and toxic microbial byproducts, most notably bacterial endotoxins. A media fill is the performance of an aseptic manufacturing procedure using a sterile microbiological growth medium, in place of the drug solution, to test whether the aseptic procedures are adequate to prevent contamination during actual drug production.



For Assistance with CMC Planning and Documentation Click Here

Damien Bové is THE Drug Development and Regulatory Consultant (pharmaceutical or biotechnology), I work with my clients to define a drug development target, define a drug development strategy, define a regulatory strategy or define a commercial strategy. Our clients are generally raising funds or looking to license out their technology and we help them achieve it. If you want to know more don’t hesitate to get in touch.

Avoid Expensive Mistakes, Keep On Top of New and Changing Regulations for Free!

Sign up for the most value add free newsource you can get for free. We spend a huge amount of time and effort monitoring the main drug / device regulators websites for changes in the regulatory environment, and capture between 20 and 40 new regulations, rules and initiatives each month, and summaries them in a fantastic FREE monthly Regulatory and Market Round Up. You can Un-Subscribe at any time and we don not share your details with anybody. You can’t afford to miss out on this service. Just fill in the form below.

Fill Out the Short Form Below…


  1. (required)


  2. (valid email required)

“Please note that the pages on this website are designed to provide you with general information only. We make no warranties, representations or undertakings about any of its content. This includes the completeness, accuracy and fitness for any particular purpose, or the content of any third party site referred to or accessed through it. You are personally responsible for ensuring that the information is correct and we will not be held liable or accountable for any mistakes that occur.”

Health Canada Publish Draft Guidnace on GMP for Medical Gases

Health Canada Publish Draft Guidance on GMP for Medical Gases

Full Text Here

The draft guidelines outlined in Good Manufacturing Practices for Medical Gases (GUI-0031), state the generally applicable principles and practices that are acceptable to the Inspectorate and that should facilitate compliance of fabricators, packagers/labellers, distributors, importers, and home care providers of medical gases with Division 2, Part C of the Food and Drug Regulations on Good Manufacturing Practices (GMP).

This guidance document was revised to reflect the current regulatory environment and to clarify certain aspects that have relevance to the companies dealing with medical gases. Due to their unique production and handling characteristics, the application of the GMP Regulations to medical gases may be different from their application to other pharmaceuticals, thus the interpretations provided in the main GMP Guidelines are replaced by those given in this document for medical gases.

The GMP guidelines are available on Health Canada’s Compliance and Enforcement website.



For Assistance with CMC Planning and Documentation Click Here

Damien Bové is THE Drug Development and Regulatory Consultant (pharmaceutical or biotechnology), I work with my clients to define a drug development target, define a drug development strategy, define a regulatory strategy or define a commercial strategy. Our clients are generally raising funds or looking to license out their technology and we help them achieve it. If you want to know more don’t hesitate to get in touch.

Avoid Expensive Mistakes, Keep On Top of New and Changing Regulations for Free!

Sign up for the most value add free newsource you can get for free. We spend a huge amount of time and effort monitoring the main drug / device regulators websites for changes in the regulatory environment, and capture between 20 and 40 new regulations, rules and initiatives each month, and summaries them in a fantastic FREE monthly Regulatory and Market Round Up. You can Un-Subscribe at any time and we don not share your details with anybody. You can’t afford to miss out on this service. Just fill in the form below.

Fill Out the Short Form Below…


  1. (required)


  2. (valid email required)

“Please note that the pages on this website are designed to provide you with general information only. We make no warranties, representations or undertakings about any of its content. This includes the completeness, accuracy and fitness for any particular purpose, or the content of any third party site referred to or accessed through it. You are personally responsible for ensuring that the information is correct and we will not be held liable or accountable for any mistakes that occur.”

FDA Publish Guidance on Physical Chemical Identifiers for Anti-Counterfeiting

FDA Publish Guidance on Physical Chemical Identifiers for Anti-Counterfeiting

Full Text Here

This document is intended to provide guidance to pharmaceutical manufacturers who want to use physical-chemical identifiers (PCIDs) in solid oral dosage forms (SODFs). A PCID is a substance or combination of substances possessing a unique physical or chemical property that unequivocally identifies and authenticates a drug product or dosage form.
This guidance provides recommendations to pharmaceutical manufacturers on (1) design considerations for incorporating PCIDS into SODFs, (2) supporting documentation to be submitted in new drug applications (NDAs) and abbreviated new drug applications (ANDAs) to address the proposed incorporation of PCIDs in SODFs, (3) supporting documentation to be submitted in postapproval submissions to report or request approval to incorporate PCIDs into SODFs, and (4) procedures for reporting or requesting approval to incorporate PCIDs into SODFs as a postapproval change.
The incorporation of components or features used in radiofrequency identification for drug products is outside the scope of this guidance. In addition, this guidance does not apply to manufacturing or formulation changes, made in conjunction with the addition of a PCID, that go beyond simply inserting the PCID into a blending or mixing operation (e.g., adding a PCID to a non-functional tablet film coating is covered by this guidance, but adding a non-functional film coating that contains a PCID to a previously uncoated tablet involves manufacturing changes that are not covered by this guidance). The incorporation of a PCID into the packaging or labeling is not covered in this guidance.
Other guidance documents, which may be applicable to proposed changes outside the scope of this guidance, are located on FDA’s guidance Web site2 and should be consulted to help to determine whether additional reporting or approval procedures may apply to proposed changes outside the scope of this guidance.


For Assistance with Changes to CMC Plans and Regulation Click Here

Damien Bové is THE Drug Development and Regulatory Consultant (pharmaceutical or biotechnology), I work with my clients to define a drug development target, define a drug development strategy, define a regulatory strategy or define a commercial strategy. Our clients are generally raising funds or looking to license out their technology and we help them achieve it. If you want to know more don’t hesitate to get in touch.

Avoid Expensive Mistakes, Keep On Top of New and Changing Regulations for Free!

Sign up for the most value add free newsource you can get for free. We spend a huge amount of time and effort monitoring the main drug / device regulators websites for changes in the regulatory environment, and capture between 20 and 40 new regulations, rules and initiatives each month, and summaries them in a fantastic FREE monthly Regulatory and Market Round Up. You can Un-Subscribe at any time and we don not share your details with anybody. You can’t afford to miss out on this service. Just fill in the form below.

Fill Out the Short Form Below…


  1. (required)


  2. (valid email required)

“Please note that the pages on this website are designed to provide you with general information only. We make no warranties, representations or undertakings about any of its content. This includes the completeness, accuracy and fitness for any particular purpose, or the content of any third party site referred to or accessed through it. You are personally responsible for ensuring that the information is correct and we will not be held liable or accountable for any mistakes that occur.”

FDA Publish Guidance on PET Drug Applications

FDA Publish Guidance on PET Drug Applications

Full Text Here

On December 9, 2009, FDA issued a final current good manufacturing practice (CGMP) regulation for the production of positron emission tomography (PET) drugs. Under the requirements of section 121 of the Food and Drug Administration Modernization Act (FDAMA), within two years following this publication date, an NDA or ANDA must be submitted for any PET drug marketed for clinical use in the United States.
This guidance is intended to assist applicants in preparing new drug applications (NDAs) or abbreviated new drug applications (ANDAs) for fludeoxyglucose F 18 injection, ammonia N 13 injection, and sodium fluoride F 18 injection used in PET imaging for the indications cited in Section III (below). FDA approval of an NDA or ANDA will make it possible to market these PET drugs for clinical use according to the requirements of the Federal Food, Drug, and Cosmetic Act (the Act).
The guidance (1) provides brief background information, (2) makes recommendations to help you decide whether you should submit an NDA or an ANDA, (3) includes a description of the content and format needed in an NDA and an ANDA, and (4) provides boxed text that you can copy or cut and paste into your application. The content and format sections provide information required to submit an NDA or an ANDA for these PET drugs. Finally, we have developed sample formats for the chemistry sections and for the proposed labeling for fludeoxyglucose F 18 injection, ammonia N 13 injection, and sodium fluoride F 18 injection as well as 356h sample forms. These formats are supplied as separate documents on FDA’s web site.
FDA’s guidance documents, including this guidance, do not establish legally enforceable responsibilities. Instead, guidances describe the Agency’s current thinking on a topic and should be viewed only as recommendations, unless specific regulatory or statutory requirements apply. The use of the word should in Agency guidances means that something is suggested or recommended, but not required.
Because this guidance discusses in great detail what must be submitted in an NDA (particularly a 505(b)(2) NDA) or an ANDA (505(j)), the guidance differs from most guidances in that it contains extensive mandatory language, especially in the Appendices. This mandatory language is used whenever the Act and/or FDA regulations require the submission of certain information. Unlike other documents in which mandatory language is accompanied by the related cite, to make the guidance more user friendly and less cumbersome, we do not cite each regulation each time we discuss a requirement.


For Assistance with Developing PET Drugs Click Here

Damien Bové is THE Drug Development and Regulatory Consultant (pharmaceutical or biotechnology), I work with my clients to define a drug development target, define a drug development strategy, define a regulatory strategy or define a commercial strategy. Our clients are generally raising funds or looking to license out their technology and we help them achieve it. If you want to know more don’t hesitate to get in touch.

Avoid Expensive Mistakes, Keep On Top of New and Changing Regulations for Free!

Sign up for the most value add free newsource you can get for free. We spend a huge amount of time and effort monitoring the main drug / device regulators websites for changes in the regulatory environment, and capture between 20 and 40 new regulations, rules and initiatives each month, and summaries them in a fantastic FREE monthly Regulatory and Market Round Up. You can Un-Subscribe at any time and we don not share your details with anybody. You can’t afford to miss out on this service. Just fill in the form below.

Fill Out the Short Form Below…


  1. (required)


  2. (valid email required)

“Please note that the pages on this website are designed to provide you with general information only. We make no warranties, representations or undertakings about any of its content. This includes the completeness, accuracy and fitness for any particular purpose, or the content of any third party site referred to or accessed through it. You are personally responsible for ensuring that the information is correct and we will not be held liable or accountable for any mistakes that occur.”

EMA Publish Template of Qualified Persons Declaration of GMP Compliance

EMA Publish Template of Qualified Persons Declaration of GMP Compliance

Full Text Here

The objective of this Qualified Person (QP) Declaration Template is to emphasise the importance of providing a comprehensive declaration, to harmonise the format for the declaration, to forestall questions during assessment, and to enhance the efficiency of the regulatory process.
The quality of medicinal products depends to a large degree on the quality of the active substances used to formulate them. Medicinal product manufacturers have the prime responsibility for ensuring the quality of active substances in terms of GMP compliance and prevention of falsification and should therefore take appropriate measures to:
(i) Verify the GMP compliance of all parties in the supply chain and that all sources are in accordance with relevant marketing authorisations.
(ii) Fully understand and control the supply chain of active substances used by them (including brokers, re-labellers and re-packagers) and take steps to shorten the supply chain wherever possible.
(iii) Clearly demonstrate that each batch of active substance accepted by them for use in the manufacture of medicinal products has been sourced through this supply chain.
In order to satisfy the above requirements, the manufacturer will submit a declaration that addresses GMP compliance and supply chain verification.
The attached QP declaration template provides, in a format considered suitable for submission, a basis for demonstrating compliance of the active substance manufacture with GMP requirements and that the manufacturer has relevant knowledge of the supply chain.
QP Declarations are required from each EEA finished product manufacturing site and/or from each site of importation/batch certification. However, a single declaration from one QP from one of the registered finished product or batch release sites may be sufficient, if its basis is satisfactorily described and supported by technical agreements between these sites (see Part B and E).
The QP Declaration should be provided in support of an application for a new marketing authorisation, variation or renewal of a medicinal product(s) authorised in the Community, using EU or national procedures within the scope of Directive 2001/83/EC1 (human medicinal products) and Directive 2001/82/EC2 (veterinary medicinal products). A declaration is not required for blood or blood components; they are subject to the requirements of Directive 2002/98/EC8.



For Assistance with CMC Documentation and Strategy Click Here

Damien Bové is THE Drug Development and Regulatory Consultant (pharmaceutical or biotechnology), I work with my clients to define a drug development target, define a drug development strategy, define a regulatory strategy or define a commercial strategy. Our clients are generally raising funds or looking to license out their technology and we help them achieve it. If you want to know more don’t hesitate to get in touch.

Avoid Expensive Mistakes, Keep On Top of New and Changing Regulations for Free!

Sign up for the most value add free newsource you can get for free. We spend a huge amount of time and effort monitoring the main drug / device regulators websites for changes in the regulatory environment, and capture between 20 and 40 new regulations, rules and initiatives each month, and summaries them in a fantastic FREE monthly Regulatory and Market Round Up. You can Un-Subscribe at any time and we don not share your details with anybody. You can’t afford to miss out on this service. Just fill in the form below.

Fill Out the Short Form Below…


  1. (required)


  2. (valid email required)

“Please note that the pages on this website are designed to provide you with general information only. We make no warranties, representations or undertakings about any of its content. This includes the completeness, accuracy and fitness for any particular purpose, or the content of any third party site referred to or accessed through it. You are personally responsible for ensuring that the information is correct and we will not be held liable or accountable for any mistakes that occur.”

EMA Publish Guidance on Stability Testings for Applications for Variations to Marketing Authorisations

EMA Publish Guidance on Stability Testings for Applications for Variations to Marketing Authorisations

Full Text Here

The following guideline provides guidance on the stability data which have to be generated in order to support a variation to a Marketing Authorisation. The guideline provides general guidance on stability testing in case of type I (A and B) variations and addresses the data requirements for widely encountered cases of type II variations.

The following guideline sets out the stability testing requirements for variations to a Marketing Authorisation after approval. This guideline is an extension of the CHMP and CVMP Guidelines on Stability Testing of Existing Active Substances and Related Finished Products and the respective ICH/VICH Guidelines for New Active Substances and Drug Products. It is intended to be applied in the European Union.
The guideline seeks to exemplify the stability data required for variations to active substances and/or finished products. It is not always necessary to follow this when there are scientifically justifiable reasons for using alternative approaches.
The guideline provides a general indication on the requirement for stability testing, but leaves sufficient flexibility to encompass the variety of different practical situations required for specific scientific situations and characteristics of the material being evaluated.

The purpose of this guideline is to outline the stability data which have to be generated in case of variations. It is applicable to chemical active substances and related finished products, herbal drugs, herbal drug preparations and related herbal medicinal products, however not to radiopharmaceuticals, biologicals and products derived from biotechnology.
Variations for active substances and finished products encompass a wide range of situations. The Guideline provides general guidance on stability testing in case of type I (A and B) variations, furthermore, it addresses the information required for active substances and/or finished products in widely encountered cases of type II variations as listed in section 6

EMA Announces Opening of Public Consultation on Good Distribution Practice

EMA Announces Opening of Public Consultation on Good Distribution Practice

Full Text Here

The European Commission’s Directorate General for Health and Consumer Policy (DG SANCO) has launched a public consultation on the revised ‘Guideline on Good Distribution Practice of Medicinal Products for Human Useicon link external EMA Announces Opening of Public Consultation on Good Distribution Practice’. The European Medicines Agency through its GMP/GDP Inspectors Working Group worked on the revision of the guideline which was first published in 1994.

The guideline was revised to take into account developments in the storage and distribution of medicinal products in the European Union and to meet new requirements for wholesale distributors and brokers established in the new Directive 2011/62/EU on falsified medicines.

The draft guideline is of particular interest to wholesale distributors and brokers of medicinal products for human use as well as for manufacturers who distribute their own products.

Comments and suggestions are invited by 31 December 2011 and should be sent by email to: SANCO-gmp@ec.europa.eu and ADM-GMDP@ema.europa.eu using this template for comments.


For Assistance with Distribution Planning and Documentation Click Here

Damien Bové is THE Drug Development and Regulatory Consultant (pharmaceutical or biotechnology), I work with my clients to define a drug development target, define a drug development strategy, define a regulatory strategy or define a commercial strategy. Our clients are generally raising funds or looking to license out their technology and we help them achieve it. If you want to know more don’t hesitate to get in touch.

Avoid Expensive Mistakes, Keep On Top of New and Changing Regulations for Free!

Sign up for the most value add free newsource you can get for free. We spend a huge amount of time and effort monitoring the main drug / device regulators websites for changes in the regulatory environment, and capture between 20 and 40 new regulations, rules and initiatives each month, and summaries them in a fantastic FREE monthly Regulatory and Market Round Up. You can Un-Subscribe at any time and we don not share your details with anybody. You can’t afford to miss out on this service. Just fill in the form below.

Fill Out the Short Form Below…


  1. (required)


  2. (valid email required)

“Please note that the pages on this website are designed to provide you with general information only. We make no warranties, representations or undertakings about any of its content. This includes the completeness, accuracy and fitness for any particular purpose, or the content of any third party site referred to or accessed through it. You are personally responsible for ensuring that the information is correct and we will not be held liable or accountable for any mistakes that occur.”

EMA Publish Guidance on Plasma-Derived Medicinal Products

EMA Publish Guidance on Plasma-Derived Medicinal Products

Full Text Here

Human plasma contains many proteins which, following extraction, purification, and formulation into medicinal products are of great medical importance. Plasma-derived products provide life-saving therapies but the quantity of plasma for fractionation is limited by the number of donors. Therefore, the exchange of intermediates between manufacturers or the use of a variant manufacturing process (see below) may be possible to assure the best use of blood/plasma donations.
Although the therapeutic use of blood transfusion goes back to the beginning of the 20th century, it was not until the 1940s that the technique of plasma fractionation, devised by Cohn and colleagues, enabled the widespread use of medicinal products extracted from human plasma.
Improvements in protein purification and molecular separation technology have made available a wide variety of products, with medical applications covering a large field, and the therapeutic value of these is unquestioned. However, the potential for viral transmission is well recognised, and because of the large number of donations which are pooled, a single contaminated batch of a plasma-derived product, with the contamination possibly originating from a single donation, can transmit viral disease to a large number of recipients. The recognition in the mid-1980′s that plasma-derived medicinal products, in particular coagulation factor concentrates, had caused widespread transmission of human immunodeficiency virus (HIV) and hepatitis C (previously identified as non-A non-B hepatitis) resulted in major changes to the manufacturing processes, with the introduction of specific steps to inactivate or remove these and other blood-borne viruses. Infectious non-enveloped viruses were detected in certain plasma-derived medicinal products during the 1990’s and early 2000’s. Therefore, recent process development has been devoted to further reducing non-enveloped viruses such as hepatitis A (HAV) and parvovirus B19 (B19V).
Measures taken to prevent infection include selection of donors, screening of individual donations and plasma pools for markers of infection with known viruses and validation of the production process for inactivation or removal of viruses. From the 1990’s on, measures designed to minimise contamination of the starting plasma have been improved by the refinement of serological test kits and the use of nucleic acid amplification technology (NAT) for the testing of viral DNA and RNA, thereby shortening the window period during which infectious donations are not detected.
Recent cases of apparent iatrogenic variant Creutzfeldt-Jakob disease (vCJD) infection by blood transfusion in man in the UK provide strong evidence that vCJD is transmissible through blood transfusion. Precautionary measures to minimize the risk of transmission of infectivity by plasma-derived medicinal products were put in place by CHMP in 1998 following the identification of the first cases of vCJD and have been kept under review and updated as needed.
The legal basis for EU minimum standards for the quality and safety of the starting material for plasma-derived medicinal products has been established along with the pharmaceutical legislation and specific provisions have been laid down in the pharmaceutical Directive 2001/83/EC as amended. In this legislation the option of a centralised certification of Plasma Master File was established.
In 2003 the European Parliament and the Council have adopted the overarching Directive 2002/98/EC “Setting standards of quality and safety for the collection, testing, processing, storage and distribution of human blood and blood components…”, also known as the “Blood Directive”. Thereby, from 8 February 2005, Directive 2002/98/EC amending Directive 2001/83/EC establishes the requirements for the collection and testing of human blood and blood components whatever the intended purpose. In line with this Directive, the technical Directives 2004/33/EC, 2005/61/EC and 2005/62/EC have been issued by the Commission. Guidance is also provided by the “Guide to the Preparation, Use and Quality Assurance of Blood Components” of the Council of Europe which contains a compendium of measures designed to ensure the safety, efficacy and quality of blood components.


For Assistance with Biological Porduct Development and Manufacturing Click Here

Damien Bové is THE Drug Development and Regulatory Consultant (pharmaceutical or biotechnology), I work with my clients to define a drug development target, define a drug development strategy, define a regulatory strategy or define a commercial strategy. Our clients are generally raising funds or looking to license out their technology and we help them achieve it. If you want to know more don’t hesitate to get in touch.

Avoid Expensive Mistakes, Keep On Top of New and Changing Regulations for Free!

Sign up for the most value add free newsource you can get for free. We spend a huge amount of time and effort monitoring the main drug / device regulators websites for changes in the regulatory environment, and capture between 20 and 40 new regulations, rules and initiatives each month, and summaries them in a fantastic FREE monthly Regulatory and Market Round Up. You can Un-Subscribe at any time and we don not share your details with anybody. You can’t afford to miss out on this service. Just fill in the form below.

Fill Out the Short Form Below…


  1. (required)


  2. (valid email required)

“Please note that the pages on this website are designed to provide you with general information only. We make no warranties, representations or undertakings about any of its content. This includes the completeness, accuracy and fitness for any particular purpose, or the content of any third party site referred to or accessed through it. You are personally responsible for ensuring that the information is correct and we will not be held liable or accountable for any mistakes that occur.”

EMA Publish Guidance on Certificates of Medicinal Products, Filling in Application Forms

EMA Publish Guidance on Certificates of Medicinal Products, Filling in Application Forms

Full Text Here

This form is intended for requesting EMA certificates of medicinal products only. It can be used as of date of publication. Requests cannot be submitted on any other form. A complete request includes Part A and Part(s) B of the form and, if applicable, a statement of composition and permission from the Marketing Authorisation Holder to obtain the certificates on their behalf. Once you have submitted the request, changes or cancellations are not accepted. A flow-chart for requesting certificates is attached at the end of these instructions and an update on “What’s new with certification?” is available on the EMA Certificates of Medicinal Products web page. Guidance to complete the forms is provided point-by-point in these explanatory notes. You can facilitate certification by avoiding submission of duplicated and other redundant information and documents in your request.



For Assistance with International Registration of Drugs and Shipping of Products Click Here

Damien Bové is THE Drug Development and Regulatory Consultant (pharmaceutical or biotechnology), I work with my clients to define a drug development target, define a drug development strategy, define a regulatory strategy or define a commercial strategy. Our clients are generally raising funds or looking to license out their technology and we help them achieve it. If you want to know more don’t hesitate to get in touch.

Avoid Expensive Mistakes, Keep On Top of New and Changing Regulations for Free!

Sign up for the most value add free newsource you can get for free. We spend a huge amount of time and effort monitoring the main drug / device regulators websites for changes in the regulatory environment, and capture between 20 and 40 new regulations, rules and initiatives each month, and summaries them in a fantastic FREE monthly Regulatory and Market Round Up. You can Un-Subscribe at any time and we don not share your details with anybody. You can’t afford to miss out on this service. Just fill in the form below.

Fill Out the Short Form Below…


  1. (required)


  2. (valid email required)

“Please note that the pages on this website are designed to provide you with general information only. We make no warranties, representations or undertakings about any of its content. This includes the completeness, accuracy and fitness for any particular purpose, or the content of any third party site referred to or accessed through it. You are personally responsible for ensuring that the information is correct and we will not be held liable or accountable for any mistakes that occur.”

The European Commission Publish Guidance on Compilation of Community Procedures on Inspections and Exchange of Information

The European Commission Publish Guidance on Compilation of Community Procedures on Inspections and Exchange of Information

Full Text Here

The Compilation of Community Procedures on Inspections and Exchange of Information, formerly known as the Compilation of Community Procedures on Administrative Collaboration and Harmonisation of Inspections, is a tool for facilitating co-operation between the GMP inspectorates of the Member States and a means of achieving harmonisation. The procedures within it provide the basis for national procedures that form part of the national GMP inspectorates’ quality systems. These quality systems are based on a framework laid down in one of the documents of the Compilation. In July 2010 documents connected with Good Distribution Practice (GDP) inspections started to be added to the Compilation.

The contents of the Compilation of Procedures are constantly updated developed and agreed, under the co-ordination of the European Medicines Agency, by representatives of the GMP Inspectorates of each member state, including those supervising the manufacture and import of veterinary medicinal products only. Once agreed, they are adopted by the European Commission and then published on its behalf by the European Medicines Agency.

The Heads of Medicines Agencies have agreed to the setting up of a joint audit programme of GMP inspectorates to maintain mutual confidence in the GMP inspection systems of each member state by the other member states, and the Compilation provides criteria on which the audits are based.

Member states are obliged to take account of the Compilation of Procedures by virtue of Art. 3(1) of Directive 2003/94/EC. Until such time as the corresponding GMP directive for veterinary medicinal products, Directive 91/412/EEC, is amended accordingly, GMP Inspectorates dealing exclusively with veterinary medicinal products have voluntarily agreed to abide by it, although it is recognised that the formats for inspection reports, manufacturing authorisations and GMP certificates are of a binding nature by virtue of Art. 51 of Directive 2001/82/EC, as amended.



For Assistance with Submitting Evidence to NICE Click Here

Damien Bové is THE Drug Development and Regulatory Consultant (pharmaceutical or biotechnology), I work with my clients to define a drug development target, define a drug development strategy, define a regulatory strategy or define a commercial strategy. Our clients are generally raising funds or looking to license out their technology and we help them achieve it. If you want to know more don’t hesitate to get in touch.

Avoid Expensive Mistakes, Keep On Top of New and Changing Regulations for Free!

Sign up for the most value add free newsource you can get for free. We spend a huge amount of time and effort monitoring the main drug / device regulators websites for changes in the regulatory environment, and capture between 20 and 40 new regulations, rules and initiatives each month, and summaries them in a fantastic FREE monthly Regulatory and Market Round Up. You can Un-Subscribe at any time and we don not share your details with anybody. You can’t afford to miss out on this service. Just fill in the form below.

Fill Out the Short Form Below…


  1. (required)


  2. (valid email required)

“Please note that the pages on this website are designed to provide you with general information only. We make no warranties, representations or undertakings about any of its content. This includes the completeness, accuracy and fitness for any particular purpose, or the content of any third party site referred to or accessed through it. You are personally responsible for ensuring that the information is correct and we will not be held liable or accountable for any mistakes that occur.”

EMA Publish Guidance on ICH Q11 on Development and Manufacture of Chemical and Biotechnology Drug Substances

EMA Publish Guidance on ICH Q11 on Development and Manufacture of Chemical and Biotechnology Drug Substances.

Full Text Here

This guideline describes approaches to developing process and drug substance understanding and also provides guidance on what information should be provided in CTD sections 3.2.S.2.2 – 3.2.S.2.6. It provides further clarification on the principles and concepts described in ICH guidelines on Pharmaceutical Development (Q8), Quality Risk Management (Q9) and Pharmaceutical Quality Systems (Q10) as they pertain to the development and manufacture of drug substance.

A company can choose to follow different approaches in developing a drug substance. For the purpose of this guideline, the terms “traditional” and “enhanced” are used to differentiate two possible approaches. In a traditional approach, set points and operating ranges for process parameters are defined and the drug substance control strategy is typically based on demonstration of process reproducibility and testing to meet established acceptance criteria. In an enhanced approach, risk management and more extensive scientific knowledge are used to select process parameters and unit operations that impact critical quality attributes (CQAs) for evaluation in further studies to establish any design space(s) and control strategies applicable over the lifecycle of the drug substance. As discussed in ICH Q8 for drug product, a greater understanding of the drug substance and its manufacturing process can create the basis for more flexible regulatory approaches. The degree of regulatory flexibility is generally predicated on the level of relevant scientific knowledge provided in the application for marketing authorisation.

Traditional and enhanced approaches are not mutually exclusive. A company can use either a traditional approach or an enhanced approach to drug substance development, or a combination of both.



For Assistance with CMC Planning and Documentaiton Click Here

Damien Bové is THE Drug Development and Regulatory Consultant (pharmaceutical or biotechnology), I work with my clients to define a drug development target, define a drug development strategy, define a regulatory strategy or define a commercial strategy. Our clients are generally raising funds or looking to license out their technology and we help them achieve it. If you want to know more don’t hesitate to get in touch.

Avoid Expensive Mistakes, Keep On Top of New and Changing Regulations for Free!

Sign up for the most value add free newsource you can get for free. We spend a huge amount of time and effort monitoring the main drug / device regulators websites for changes in the regulatory environment, and capture between 20 and 40 new regulations, rules and initiatives each month, and summaries them in a fantastic FREE monthly Regulatory and Market Round Up. You can Un-Subscribe at any time and we don not share your details with anybody. You can’t afford to miss out on this service. Just fill in the form below.

Fill Out the Short Form Below…


  1. (required)


  2. (valid email required)

“Please note that the pages on this website are designed to provide you with general information only. We make no warranties, representations or undertakings about any of its content. This includes the completeness, accuracy and fitness for any particular purpose, or the content of any third party site referred to or accessed through it. You are personally responsible for ensuring that the information is correct and we will not be held liable or accountable for any mistakes that occur.”

EMA Publishes Guidance on Stability Testing

EMA Publishes Guidance on Stability Testing

Full Text Here

The following guideline provides guidance on the stability data which have to be generated in order to support a variation to a Marketing Authorisation. The guideline provides general guidance on stability testing in case of type I (A and B) variations and addresses the data requirements for widely encountered cases of type II variations.

The following guideline sets out the stability testing requirements for variations to a Marketing Authorisation after approval. This guideline is an extension of the CHMP and CVMP Guidelines on Stability Testing of Existing Active Substances and Related Finished Products and the respective ICH/VICH Guidelines for New Active Substances and Drug Products. It is intended to be applied in the European Union.
The guideline seeks to exemplify the stability data required for variations to active substances and/or finished products. It is not always necessary to follow this when there are scientifically justifiable reasons for using alternative approaches.
The guideline provides a general indication on the requirement for stability testing, but leaves sufficient flexibility to encompass the variety of different practical situations required for specific scientific situations and characteristics of the material being evaluated.

The purpose of this guideline is to outline the stability data which have to be generated in case of variations. It is applicable to chemical active substances and related finished products, herbal drugs, herbal drug preparations and related herbal medicinal products, however not to radiopharmaceuticals, biologicals and products derived from biotechnology.
Variations for active substances and finished products encompass a wide range of situations. The Guideline provides general guidance on stability testing in case of type I (A and B) variations, furthermore, it addresses the information required for active substances and/or finished products in widely encountered cases of type II variations as listed in section 6.



For Assistance with Submitting Evidence to NICE Click Here

Damien Bové is THE Drug Development and Regulatory Consultant (pharmaceutical or biotechnology), I work with my clients to define a drug development target, define a drug development strategy, define a regulatory strategy or define a commercial strategy. Our clients are generally raising funds or looking to license out their technology and we help them achieve it. If you want to know more don’t hesitate to get in touch.

Avoid Expensive Mistakes, Keep On Top of New and Changing Regulations for Free!

Sign up for the most value add free newsource you can get for free. We spend a huge amount of time and effort monitoring the main drug / device regulators websites for changes in the regulatory environment, and capture between 20 and 40 new regulations, rules and initiatives each month, and summaries them in a fantastic FREE monthly Regulatory and Market Round Up. You can Un-Subscribe at any time and we don not share your details with anybody. You can’t afford to miss out on this service. Just fill in the form below.

Fill Out the Short Form Below…


  1. (required)


  2. (valid email required)

“Please note that the pages on this website are designed to provide you with general information only. We make no warranties, representations or undertakings about any of its content. This includes the completeness, accuracy and fitness for any particular purpose, or the content of any third party site referred to or accessed through it. You are personally responsible for ensuring that the information is correct and we will not be held liable or accountable for any mistakes that occur.”

EMA Announces Meeting on Systems and Process Lifecycles in Pharmaceutical Manufacturing

EMA Announces Meeting on Systems and Process Lifecycles in Pharmaceutical Manufacturing

Full Text Here

The Parenteral Drug Association, the International Society for Pharmaceutical Engineering, the Food and Drug Administration and the European Medicines Agency are creating a special joint conference dedicated to teaching the principles of International Conference on Harmonisation of Technical Requirements for Registration of Pharmaceuticals for Human Use (ICH) Q10. This is a unique opportunity to learn these principles from companies that have implemented a pharmaceutical quality system across the product lifecycle according to the ICH Q10 model.



For Assistance with CMC Planning and Documentation in the EU or USA Click Here

Damien Bové is THE Drug Development and Regulatory Consultant (pharmaceutical or biotechnology), I work with my clients to define a drug development target, define a drug development strategy, define a regulatory strategy or define a commercial strategy. Our clients are generally raising funds or looking to license out their technology and we help them achieve it. If you want to know more don’t hesitate to get in touch.

Avoid Expensive Mistakes, Keep On Top of New and Changing Regulations for Free!

Sign up for the most value add free newsource you can get for free. We spend a huge amount of time and effort monitoring the main drug / device regulators websites for changes in the regulatory environment, and capture between 20 and 40 new regulations, rules and initiatives each month, and summaries them in a fantastic FREE monthly Regulatory and Market Round Up. You can Un-Subscribe at any time and we don not share your details with anybody. You can’t afford to miss out on this service. Just fill in the form below.

Fill Out the Short Form Below…


  1. (required)


  2. (valid email required)

“Please note that the pages on this website are designed to provide you with general information only. We make no warranties, representations or undertakings about any of its content. This includes the completeness, accuracy and fitness for any particular purpose, or the content of any third party site referred to or accessed through it. You are personally responsible for ensuring that the information is correct and we will not be held liable or accountable for any mistakes that occur.”

EMA Announce Meeting on Lifecycles in Pharmaceutical Manufacturing

EMA Announce Meeting on Lifecycles in Pharmaceutical Manufacturing

Full Text Here

The Parenteral Drug Association, the International Society for Pharmaceutical Engineering, the Food and Drug Administration and the European Medicines Agency are creating a special joint conference dedicated to teaching the principles of International Conference on Harmonisation of Technical Requirements for Registration of Pharmaceuticals for Human Use (ICH) Q10. This is a unique opportunity to learn these principles from companies that have implemented a pharmaceutical quality system across the product lifecycle according to the ICH Q10 model.


For Assistance with CMC Planning and Documentation Click Here

Damien Bové is THE Drug Development and Regulatory Consultant (pharmaceutical or biotechnology), I work with my clients to define a drug development target, define a drug development strategy, define a regulatory strategy or define a commercial strategy. Our clients are generally raising funds or looking to license out their technology and we help them achieve it. If you want to know more don’t hesitate to get in touch.

Avoid Expensive Mistakes, Keep On Top of New and Changing Regulations for Free!

Sign up for the most value add free newsource you can get for free. We spend a huge amount of time and effort monitoring the main drug / device regulators websites for changes in the regulatory environment, and capture between 20 and 40 new regulations, rules and initiatives each month, and summaries them in a fantastic FREE monthly Regulatory and Market Round Up. You can Un-Subscribe at any time and we don not share your details with anybody. You can’t afford to miss out on this service. Just fill in the form below.

Fill Out the Short Form Below…


  1. (required)


  2. (valid email required)

“Please note that the pages on this website are designed to provide you with general information only. We make no warranties, representations or undertakings about any of its content. This includes the completeness, accuracy and fitness for any particular purpose, or the content of any third party site referred to or accessed through it. You are personally responsible for ensuring that the information is correct and we will not be held liable or accountable for any mistakes that occur.”

 

FDA Publish Guidance on Donor History Questionnaires for Screening Donors of Source Plasma

FDA Publish Guidance on Donor History Questionnaires for Screening Donors of Source Plasma

Full Text Here

This guidance recognizes the standardized full-length and abbreviated donor history questionnaires and accompanying materials, version 1.0.1 dated December 2010, prepared by the Plasma Protein Therapeutics Association (PPTA) as an acceptable mechanism that is consistent with the Food and Drug Administration’s (FDA’s) requirements and recommendations for collecting Source Plasma donor history information. We, FDA, may recognize other PPTA Source Plasma donor history questionnaires and accompanying materials (SPDHQ documents) as acceptable, and intend to make all of the acceptable SPDHQ documents available on the FDA website.
The SPDHQ documents will provide blood establishments that collect Source Plasma (referred to as “manufacturers” or “you”), with a specific process for administering questions to Source Plasma donors (referred to as “donors”) to determine their eligibility to donate. We are using the term “eligibility” in this guidance to refer to the donor suitability requirements described in Title 21 Code of Federal Regulations 640.63 (21 CFR 640.63). Acceptable SPDHQ documents are those documents that FDA has determined will provide Source Plasma manufacturers with one means of obtaining donor history information from a Source Plasma donor to determine if the donor is eligible consistent with the requirements in 21 CFR 640.63.
This guidance also advises Source Plasma manufacturers who choose to implement the acceptable SPDHQ documents on how to report the manufacturing change consisting of the implementation of the SPDHQ under 21 CFR 601.12 (§ 601.12).

For Assistance with CMC Biotechnology Issues Click Here

Damien Bové is THE Drug Development and Regulatory Consultant (pharmaceutical or biotechnology), I work with my clients to define a drug development target, define a drug development strategy, define a regulatory strategy or define a commercial strategy. Our clients are generally raising funds or looking to license out their technology and we help them achieve it. If you want to know more don’t hesitate to get in touch.

Avoid Expensive Mistakes, Keep On Top of New and Changing Regulations for Free!

Sign up for the most value add free newsource you can get for free. We spend a huge amount of time and effort monitoring the main drug / device regulators websites for changes in the regulatory environment, and capture between 20 and 40 new regulations, rules and initiatives each month, and summaries them in a fantastic FREE monthly Regulatory and Market Round Up. You can Un-Subscribe at any time and we don not share your details with anybody. You can’t afford to miss out on this service. Just fill in the form below.

Fill Out the Short Form Below…


  1. (required)


  2. (valid email required)

“Please note that the pages on this website are designed to provide you with general information only. We make no warranties, representations or undertakings about any of its content. This includes the completeness, accuracy and fitness for any particular purpose, or the content of any third party site referred to or accessed through it. You are personally responsible for ensuring that the information is correct and we will not be held liable or accountable for any mistakes that occur.”

 

FDA Publishes Guidance on Donors of Blood and Blood Components: Notification of Donor Deferral

FDA Publishes Guidance on Donors of Blood and Blood Components: Notification of Donor Deferral

Full text Here

The Food and Drug Administration (FDA) has prepared this guidance in accordance with section 212 of the Small Business Regulatory Enforcement Fairness Act of 1996 (Public Law 104-121). According to the Small Business Administration, a “small business” within the blood industry is an enterprise with $10 million in average annual receipts.1 This guidance is intended to help you, a small entity that collects blood or blood components for transfusion or for further manufacturing (blood or blood components), better understand and comply with the regulatory framework set forth in Title 21 Code of Federal Regulations 630.6 (21 CFR 630.6). This provision requires you to make reasonable attempts to notify donors, including autologous donors, that they are deferred based on the results of tests for evidence of infection with a communicable disease agent(s) as required by 21 CFR 610.41, or determined not to be suitable for donation due to failure to satisfy suitability criteria under 21 CFR 640.3 or 21 CFR 640.63. This provision also requires you to notify the referring physician of an autologous donor when the autologous donor is deferred based on tests for evidence of infection with a communicable disease agent(s).

For Assistance with FDA CMC Compliance Click Here

Damien Bové is THE Drug Development and Regulatory Consultant (pharmaceutical or biotechnology), I work with my clients to define a drug development target, define a drug development strategy, define a regulatory strategy or define a commercial strategy. Our clients are generally raising funds or looking to license out their technology and we help them achieve it. If you want to know more don’t hesitate to get in touch.

Avoid Expensive Mistakes, Keep On Top of New and Changing Regulations for Free!

Sign up for the most value add free newsource you can get for free. We spend a huge amount of time and effort monitoring the main drug / device regulators websites for changes in the regulatory environment, and capture between 20 and 40 new regulations, rules and initiatives each month, and summaries them in a fantastic FREE monthly Regulatory and Market Round Up. You can Un-Subscribe at any time and we don not share your details with anybody. You can’t afford to miss out on this service. Just fill in the form below.

Fill Out the Short Form Below…


  1. (required)


  2. (valid email required)

“Please note that the pages on this website are designed to provide you with general information only. We make no warranties, representations or undertakings about any of its content. This includes the completeness, accuracy and fitness for any particular purpose, or the content of any third party site referred to or accessed through it. You are personally responsible for ensuring that the information is correct and we will not be held liable or accountable for any mistakes that occur.”

Oxygen Healthcare (O2h) to Provide Chemistry Support to Chromocell

Oxygen Healthcare (O2h) to Provide Chemistry Support to Chromocell

Oxygen Healthcare Ltd. (O2h), a Piramal Group Company and Chromocell Corporation, an emerging life sciences company active in both flavors and therapeutics discovery, today signed an agreement under which O2h will provide supplemental chemistry support to further accelerate the drug discovery initiatives at Chromocell.

“I have known O2h for a number of years and am impressed by its delivery focus,” said David Palling, Senior Vice President, Therapeutics, Chromocell. “With the in-house chemistry resources and the faster-than-expected progress made in our therapeutic programs, complementary support from O2h will help us maximize resources and reach our end-points quicker.  I look forward to this opportunity of working with them to advance our drug discovery pipeline.”

O2h will provide Chromocell during 2011 with focused libraries of compounds at mg-g scale for various projects.

Sunil Shah, CEO, O2h said “O2h has optimized its operations for discovery speed and delivery to help accelerate drug discovery efforts of companies in the United States, Europe and Japan. It is our privilege to work with the experienced team led by Dr. Palling at Chromocell,”

For Assistance with FDA CMC Documentation and Planning Click Here

Damien Bové is THE Drug Development and Regulatory Consultant (pharmaceutical or biotechnology), I work with my clients to define a drug development target, define a drug development strategy, define a regulatory strategy or define a commercial strategy. Our clients are generally raising funds or looking to license out their technology and we help them achieve it. If you want to know more don’t hesitate to get in touch.

Avoid Expensive Mistakes, Keep On Top of New and Changing Regulations for Free!

Sign up for the most value add free newsource you can get for free. We spend a huge amount of time and effort monitoring the main drug / device regulators websites for changes in the regulatory environment, and capture between 20 and 40 new regulations, rules and initiatives each month, and summaries them in a fantastic FREE monthly Regulatory and Market Round Up. You can Un-Subscribe at any time and we don not share your details with anybody. You can’t afford to miss out on this service. Just fill in the form below.

Fill Out the Short Form Below…


  1. (required)


  2. (valid email required)

“Please note that the pages on this website are designed to provide you with general information only. We make no warranties, representations or undertakings about any of its content. This includes the completeness, accuracy and fitness for any particular purpose, or the content of any third party site referred to or accessed through it. You are personally responsible for ensuring that the information is correct and we will not be held liable or accountable for any mistakes that occur.”